Int.
Journal of Renewable Energy Development 8 .
2019: 215-224 P a g e | 215 Contents list available at IJRED website Int.
Journal of Renewable Energy Development (IJRED) Journal homepage: http://ejournal.
id/index.
php/ijred Research Article Gasification of Pelletized Corn Residues with Oxygen Enriched Air and Steam Poramate Sittisuna.
Nakorn Tippayawongb,*, and Sirivatch Shimpaleec School of Energy and Environment.
University of Phayao.
Thailand Department of Mechanical Engineering.
Faculty of Engineering.
Chiang Mai University.
Thailand Department of Chemical Engineering.
College of Engineering and Computing.
University of South Carolina.
USA ABSTRACT.
This work studied generation of producer gas using oxygen-enriched air and steam mixture as gasifying medium.
Corn residues consisting of cobs and stover were used as biomass feedstock.
Both corn residues were pelletized and gasified separately with normal air, oxygen enriched air and steam mixture in a fixed bed reactor.
Effects of oxygen concentration in enriched air .
-50%), equivalence ratio .
, and steam to biomass ratio .
on the yield of product gas, the combustible gas composition such as H2.
CO, and CH4, the lower heating value (LHV), and the gasification efficiency were investigated.
It was found that the decrease in nitrogen dilution in oxygen enriched air increased proportion of combustible gas components, improved the LHV of producer gas, but gasification efficiency was not affected.
The increase in equivalence ratio favoured high product gas yield but decreased combustible gas components and LHV.
It was also observed that introduction of steam enhanced H2 production but excessive steam degraded fuel gas quality and decreased gasification efficiency.
The highest gasification efficiency of each oxygen concentration was at equivalence ratio of 0.
3 and steam to biomass ratio of 0.
58 for cob, and 0.
22 and 0.
68 for stover, respectively.
A2019.
CBIORE-IJRED.
All rights reserved Keywords: Agricultural residues.
Biomass energy.
Producer gas.
Thermochemical conversion.
Renewable energy Article History: Received: May 26, 2019.
Revised: August 17th 2019.
Accepted: Oct 6th 2019.
Available online: Oct 30th 2019 How to Cite This Article: Sittisun.
Tippayawong.
, and Shimpalee.
Gasification of pelletized corn residues with oxygen enriched air and steam.
International Journal of Renewable Energy Development, 8.
, 215-224.
https://doi.
org/10.
14710/ijred.
Introduction Most common method of gasification is using air as reacting agent.
This method is straight forward and very simple, requiring less capital and operating cost (Tippayawong et al.
, 2011.
However, presence of inert nitrogen in air dilutes the gas and hence lowers the heating value per unit volume of gas.
Oxygen agent involves expensive cost.
Steam agent consumes large amount of energy for heating enough steam temperature and requires steam recovery system.
Many researchers studied the ways to improve product gas quality.
Wongsiriamnuay et al.
improve product gas by using catalyst in the process.
The presence of catalyst was found to increase the amount of H2 and CO.
However, catalyst recovery was required.
Lv et al.
studied the characteristics of biomass air- steam gasification in a fluidized bed.
Compared with biomass air gasification, the introduction of steam greatly improved heating value .
7 to 9.
1 MJ/m.
, gas yield and carbon conversion Campoy et al.
studied the effect of oxygen in the gasification agent by enriched air- steam biomass gasification in a fluidized bed gasifier.
The oxygen content in the enriched air was varied from 21 to 40%.
The experimental result showed that the enrichment of air made it possible to increase the gasification efficiency from 54 to 68% and the LHV of the gas from 5 to 9.
3 MJ/m3, while reaching maximum carbon conversion of 97%.
From previous studies, it was found that addition of steam can improve air gasification, the use of enriched air reduces the nitrogen dilution effect, improve product gas quality and gasification efficiency.
Using enriched air steam mixtures as gasification agent has been found relatively rare.
Moreover, many researchers investigated medium calorific value gas production from biomass gasification in a fluidized bed which is suitable for medium to large scale.
Only a few studies explore medium calorific value gas production in small and medium scale fixed bed Therefore, the focus of this work is small to medium-scale plant from biomass gasification in fixed bed gasifier by using oxygen enriched air-steam as gasifying Corresponding author: n.
tippayawong@yahoo.
A IJRED Ae ISSN: 2252-4940.
All rights reserved Citation: Sittisun.
Tippayawong.
, and Shimpalee.
Gasification of pelletized corn residues with oxygen enriched air and steam.
Int.
Journal of Renewable Energy Development, 8.
, 215-224, doi.
org/10.
14710/ijred.
P a g e | 216 These 21-50% O2 content in air are chosen because they are the oxygen concentrations that can be produced using commercial air separators based on membrane technologies (Wang et al.
, 2.
Producing oxygen this way keeps the investment and operational costs relatively low, compared to processes that need high oxygen content above 50%, usually based on pressure swing adsorption or distillation units.
generator and air providing, gas cleaning unit, gas metering, gas sampling bag and gas offline analyzer.
The reactor was made from stainless steel pipe.
The height of the reactor was 105 cm and inside diameter of 55 mm.
was divided in two sections, the upper was cooling section, surrounded by cooling water.
Temperature in this zone was not over 50AC.
The lower was a heating section, surrounded and controlled by 5 kW electrical heater with insulated covering.
The reactor was installed with K-type thermocouples to control reactor temperature, monitor temperature of sampling biomass, gas in and gas out during reaction.
The outlet of the reactor connects to the cleaning unit which consisted of 8 tubes of isopropanol and placed in - 20AC ice bath for removing tar and other condensable in obtaining gas.
The gas keeps absorbing humidity by silica gel and then passing to a volumetric gas meter for gas yield measuring.
The meter was calibrated with bubble flow meter and rotameter before using.
The gas was collected in multi- layer foil gas bag.
At each experimental run, the reactor temperature was isothermally controlled at 800AC.
About 15 g of samples was loaded in the sampling basket, placed in cooling section, hermetically seal and vacuum the reactor to remove out the air.
The temperature in this zone was not over 40AC.
After the temperature reached the desiring point and steady, the basket was moved down into the middle of the heating section.
Gasifying agent such as air, oxygen- enriched air and steam were fed at the same time under various operating conditions of oxygen content (OC of 21, 30, 40, and 50% O.
, equivalence ratio ( ER of 0.
2, 0.
25, 0.
3, and 0.
and steam to biomass ratio (SB of 0, 0.
2, 0.
4, 0.
6, and 0.
The biomass was gasified together with collecting the gas for 15 min.
After that, stop feeding Materials and Methods 1 Sample preparation Corn cob and stover were collected from agricultural areas in Nan.
Thailand.
The cob and stover were ground with hammer mill to reduce the size and screened particle to less than 3 mm.
They were characterized .
esults shown in Table .
, separately formed to pellet with cylindrical die and hydraulic piston with control pressure 200 MPa and temperature 80AC with 8 mm.
diameter to get EN 14961-2 standard (Wongsiriamnuay and Tippayawong, 2.
The pellet materials were subsequently dried at 103AC for 3 days to remove humidity and stored in a desiccator to control humidity.
2 Experimental setup and procedure A laboratory scale fix bed gasifier was used in this study.
It was modified in the previous setup ( Wonsiriamnuay et , 2.
Schematic diagram and picture of setup is shown in Figure 1.
Its components consist of fixed bed reactor, sampling grate, temperature control, steam Sample thermocouple Cooling water Temperature Cooling water Controller Electrical Steam generator Air/Enriched air Fixed grate Water Cleaning unit Reactor thermocouple Gas outlet Gas Chromatography Collecting sample Gas Meter Silica gel Fig.
1 Schematic of gasification setup.
A IJRED Ae ISSN: 2252-4940.
All rights reserved Int.
Journal of Renewable Energy Development 8 .
2019: 215-224 P a g e | 217 Table 1 Properties of corn cob and stover on dry basis (% w/.
Corn cob Corn stover Volatile matter Fixed carbon Ash the agents, move the basket up into cooling section together with nitrogen feeding to stop the reaction.
After the process, the dried gas was measured by dry gas meter, the left solid was weighed, and the amount of liquid in the glass condenser was measured by taking the difference in mass before and after the test.
The gas product was immediately analyzed to find the composition.
This research focuses on gas production.
The compositions of char and liquid productions were not analyzed in their heat content of that biomass when it was totally burnt, were calculated by Eqs.
2 and 3, respectively.
ycycyc = yaya.
yiyny%ycya yaya.
yiycy%ycyc ycye.
ynyny%ycycye .
yuyeO = ycyeOyeCyei yycycycyeOyeCyei yeayeEyeOyeayeayeCyeiyei yycycycyeEyeOyeayeayeCyeiyei yyayaya% Table 3 Ranges of experimental data For Air .
% O.
Corn cob
H2 (%)
Corn stover
CO (%)
CH4 (%)
LHV (MJ/m ) Gas efficiency (%) H2 (%) CO (%) 3 Data analysis CH4 (%) Mass balance for the gasification process was checked.
The mass of gas was calculated from LHV (MJ/m.
Gas efficiency (%) H2 (%) CO (%) CH4 (%) LHV (MJ/m.
Gas efficiency (%) H2 (%) CO (%) CH4 (%) ycE"#$ ycO"#$ = yco"#$ ycIycN The gas chromatography model GC-8A.
Shimadzu was used to analyze gas composition of H2.
O2.
N2.
CH4.
CO and CO2 with Shin-carbon column and high purifying helium was carrier gas.
Gas lower heating value (LHV) which showed the quantity of heat released by combustion, a specific amount of fuel under normal condition, and gasification efficiency .
uyeO ) which were the ratios of the heat content of the fuel gas generated by the gasification of the biomass and of the For 30% O2 For 40% O2 For 50% O2 LHV (MJ/m ) Gas efficiency (%) Table 2 Regressions for each response Response (Y) Regression equations.
Y = f (OC.
ER.
SB) Cob gasification Gas .
0136 - 0.
03765 OC 6.
187 ER 0.
4016 SB 0.
000577 OC2 - 0.
09478 OC*ER - 0.
002604 OC*SB - 0.
253 ER*SB
Solid .
22794 - 0.
40980 ER - 0.
07613 SB 0.
1167 ER*SB
H2 (%)
1486 OC - 23.
31 ER 22.
717 SB - 12.
160 SB2 0.
1469 OC*ER - 9.
80 ER*SB
CO (%)
2130 OC - 62.
56 ER 2.
96 SB - 56.
6 ER2 4.
426 SB2 0.
2011 OC*ER - 0.
057 OC*SB 11.
44 ER*SB
CH4 (%)
2485 OC - 24.
19 ER - 1.
334 SB - 0.
001876 OC2 16.
84 ER2 - 1.
014 SB2 - 0.
027 OC*SB 3.
91 ER*SB
LHV (MJ/m.
1476 OC - 16.
39 ER 1.
561 SB - 0.
000762 OC2 10.
24 ER2 - 2.
297 SB2 - 0.
01524 OC*SB 1.
961 ER*SB
0 ER 20.
86 SB - 102.
7 ER2 - 15.
24 SB2 - 13.
36 ER*SB
yuC" (%) Stover gasification Gas .
9074 - 0.
03258 OC 6.
615 ER 0.
4183 SB 0.
000459 OC2 - 2.
360 ER2- 0.
08174 OC*ER - 0.
270 ER*SB
Solid .
24176 - 0.
4020 ER - 0.
07207 SB 0.
0994 ER*SB
H2 (%)
3612 OC - 35.
95 ER 27.
04 SB - 0.
003479 OC2 - 13.
29 SB2 0.
300 OC*ER- 0.
0703 OC*SB - 8.
29 ER*SB
CO (%)
1814 OC - 15.
64 ER - 4.
68 SB - 39.
8 ER2 - 2.
58 SB2 0.
2133 OC*ER 7.
57 ER*SB
CH4 (%)
2692 OC - 23.
87 ER - 4.
499 SB - 0.
001826 OC2 21.
86 ER2 1.
953 SB2 - 0.
1140 OC*ER - 0.
OC*SB 5.
88 ER*SB
LHV (MJ/m.
1704 OC - 12.
915 ER 1.
184 SB - 0.
001071 OC2 - 1.
379 SB2 - 0.
02982 OC*SB 2.
496 ER*SB
0 ER 20.
34 SB - 228.
1 ER2 - 8.
92 SB2- 16.
98 ER*SB
yuC" (%) A IJRED Ae ISSN: 2252-4940.
All rights reserved Citation: Sittisun.
Tippayawong.
, and Shimpalee.
Gasification of pelletized corn residues with oxygen enriched air and steam.
Int.
Journal of Renewable Energy Development, 8.
, 215-224, doi.
org/10.
14710/ijred.
P a g e | 218 The experimental data were statistically analyzed to create regression equations and identify the significant parameters affecting the production.
Analysis of variances was used to analyze the model significance by Minitab 17.
Generally, the significant terms of the factors are considered by p-value.
The p-value less than 0.
05 is considered as with statistically significant, and the terms of p-value higher than 0.
05 is considered to be insignificant with 95% of confidence level.
The insignificant terms were eliminated with no damaging the predictions, the regressions of each response are derived, and shown in Table 2 .
To visualize the effects of the factors, they were plotted in three-dimensional response .
Results and Discussion Effect of air, oxygen-enriched air and steam gasification were carried out under various operating conditions of oxygen content (OC: 21, 30, 40, and 50% O.
, equivalence ratio (ER: 0.
15, 0.
2, 0.
25, 0.
3, and 0.
and steam-tobiomass ratio (SB: 0, 0.
2, 0.
4, 0.
6, and 0.
Both of corn residues behaved in the same trend when the operating conditions are varied.
The ranges of the obtained experimental data are shown in Table 3.
1 Effect of operating conditions on gas production The regressions were plotted in 3D surfaces to show the effects of operating relations of OC.
ER and SB as shown in Figure 2.
Both biomass materials showed similar .
Fig.
2 Effect of operating condition on gas production in m3 per kg biomass .
hown as Y-axi.
from gasification of corn cob .
and stover .
SB = 0.
ER = 0.
25, and (C) OC = 30% A IJRED Ae ISSN: 2252-4940.
All rights reserved Int.
Journal of Renewable Energy Development 8 .
2019: 215-224 P a g e | 219 The gas production increased with ER and SB, while decreased with OC.
Increasing OC had the most impact on gas production, followed by ER and SB, respectively.
The increasing of ER increased the amount of air feeding in the system, resulted on the higher gas production.
The increased gas was not only from the higher air supply, but also from char decomposition by oxidation, partial oxidation.
Bouduard reaction, methanation, and tar Gas productions at the condition of air gasification with ER of 0.
25 were 1.
55 and 1.
54 Nm3/kg for cob and stover.
Wongsiriamnuay et al.
reported a similar range of air gasification from 1.
4 to 1.
Nm3/kg using bamboo and mimosa fixed bed gasification.
Gas production was high in air gasification.
The use of oxygen enriched air reduced the gas yield.
The reduction was mainly from the lower proportion of nitrogen.
With the increase of OC, nitrogen was decreased while the amount of the intake oxygen remained the same.
The energy for heating the adjacent nitrogen was decreased in a higher OC condition, affecting the approach to obtain faster and higher temperature, tar was cracked into gas However, the tar conversion did not affect the gas production, compared to the decrease in nitrogen.
With introduction of steam, the gas production increased significantly.
This can be explained by the fact that the steam reacted with char through water-gas reaction to form H2 and CO gases.
Tar was cracked and reformed via steam reforming to enable more gas With increasing SB, more steam was available for these reactions and these reactions were favourable at temperature above 800AC (Wei et al.
, 2007.
Lv et al.
, 2004.
Kumar et al.
, 2.
Using high steam together with high ER in the gasification process, the gas production was less increased, compared to low ER.
This was due to the competition of these agents in reacting with char.
ER was more reactive than SB.
Interaction effect between OC and SB was not significant.
Increasing SB in any enriched air gasification increased gas production in similar fashion.
The highest gas production was obtained at air gasification with ER of 0.
35 and SB of 0.
The lowest was at 50% OC enriched air gasification and ER of 0.
2 Effect of operating conditions on solid yields Amount of solid residue from gasification of both materials were significant only by the effects of ER and SB.
It was shown that increasing ER and SB decrease the amount of char residue.
Increasing ER decreased char residues from 5 to 1.
2 g/kg biomass for cob, and from 2.
9 to 2.
g/ kg biomass for stover.
When more ER was introduced, more oxygen was available to enhance oxidation reactions.
The oxidation also produced CO2 that could react with char through Bouduard reaction, resulted in decreased Increasing SB at a fixed ER of 0.
25 decreased the solid residue from around 1.
9 to1.
3 and around 2.
4 to 1.
g/ kg biomass for cob and stover, respectively.
Increasing SB favoured a reaction in solid carbon and water through water- gas reaction.
Methanation was an important reaction that H2 from the process reacted with solid char.
However, char decreased faster when ER increased.
Similar results were obtained from other reported works .
Fig.
3 Effect of operating condition on solid production in % w/w .
hown as Y-axi.
in corn .
cob and .
stover gasification ( Yuzbasi and Selcuk, 2011.
Li et al.
, 2.
The reaction rate of char reacting with oxygen was higher than reacting with steam (Huynh et al.
, 2.
SB and ER were potential candidates to react with solid char as mentioned Inputting steam in a high ER condition, carbon from the solid was available less to react with steam than at the lower ER.
The insignificance of OC on char production can be explained by the fact that the same amount of reacting oxygen was available in the process, hence, the oxidation was the same.
In Figure 3, the remaining char from cob gasification seemed to be less than stover gasification.
This was expected due to less volatile and higher density in stover pellets, because applying the same pelleting condition at the compression pressure of 200 MPa, temperature of 60AC with 2 g of each pellet, the length of stover pellets was shorter.
3 Effect of operating conditions on combustible gases All parameters were significant for combustible gas composition of both materials.
Both feedstocks behaved similarly when the process parameters changed.
Increasing OC and SB favoured the H2 production, contrasting to increasing ER which decreased H2 CO was significantly influenced by OC.
Figures 4 to 6 show the plots of the H2.
CO, and CH4.
The CH4 contents were generally lower than H2 and CO.
They varied in the range between 2 to 9%.
The increase in OC from 21 to 50% was found to increase all combustible gas components.
This was because higher OC reduced nitrogen dilution, hence higher concentration of the other gases, including H2.
CO.
A IJRED Ae ISSN: 2252-4940.
All rights reserved Citation: Sittisun.
Tippayawong.
, and Shimpalee.
Gasification of pelletized corn residues with oxygen enriched air and steam.
Int.
Journal of Renewable Energy Development, 8.
, 215-224, doi.
org/10.
14710/ijred.
P a g e | 220 and CH4.
Some additional H2 and CO were also expected from tar conversion.
However, the increase in CO was higher than the increase in H2, similar to that reported by Niu et al.
( 2.
This was due to the strengthened endothermic reactions of Bouduard and water- gas at higher OC.
Meanwhile, the H2.
CO, and CH4 composition were observed to gradually decrease when ER increased from 15 to 0.
All of them decreased at a lower OC condition.
Increasing ER boosted the air into the process in which it may dilute the producer gas.
The additional oxygen also favoured the oxidation of solid carbon and combustible gases, and reduced partial oxidation in which H2.
CO, and CH4 were consumed and CO2 was formed.
The increase in ER also reduced durations for gasification reactions.
There was the competition for oxygen among different species present in the gasifier: H2.
CO.
CH4, char, tar, etc.
It was likely that H2 and CO reacted with the additional oxygen since they were more reactive species ( Fu et al.
, 2.
However, the oxidations released the heat and the temperature was increased with the amount of ER.
High temperature allowed endothermic reactions such as Boudouard, steam reforming, and tar cracking to occur.
and CO were supposed to be generated, but oxidation was more predominant.
H2 production increased rapidly after introducing steam into the process.
The increase was due to increasing reactions between steam with solid carbon.
CO and CH4 by water- gas, water- gas shift and steam reforming.
Rupesh et al.
( 2.
explained that increasing H2 was mainly due to the effect of exothermic water gas shift Having steam in low ER conditions appeared to generate more H2 than at higher ER.
Steam promoted H2 production, but degraded CO and CH4 production.
The reduction in CH4 was due to the steam reforming.
The CO production increased slightly first and then decreased.
This was from the balance of the reactions among water-gas, water-gas shift, and steam At low SB condition, water-gas and steam reforming reactions were quite effective in increasing CO and H2.
Increasing more steam lowered gasification temperature and the effects of endothermic reactions.
The highest H2 production of 24.
15% from cob gasification was achieved at 50% OC, 0.
15 ER and 0.
8 SB, while 23.
9% was for stover gasification at the same condition.
Fig.
4 Effect of operating conditons on H2 production in % v/v .
hown as Y-axi.
from gasification of corn cob .
and stover .
SB = 4 .
ER = 0.
25, and .
OC = 30% A IJRED Ae ISSN: 2252-4940.
All rights reserved Int.
Journal of Renewable Energy Development 8 .
2019: 215-224 P a g e | 221 4 Effect of operating conditions on LHV The LHV was calculated based on the proportion of combustible gas contents (H2.
CO and CH.
Heat contribution of H2.
CO, and CH4 are 12.
78, 12.
71, and 76 MJ/m3, respectively.
The surface plots are shown in Figure 7.
OC had the most significant effect on LHV, followed by ER.
The LHV was improved as OC and ER At ER of 0.
25, the LHV from air gasification of corn cob was 4.
04 MJ/m3, and stover was 4.
21 MJ/m3.
Increasing OC to 50% improved LHV to 6.
77 MJ/m3 for cob, and 6.
94 MJ/m3 for stover.
The increases were about 68% and 65%, respectively.
The behavior observed can be explained by the analysis of combustible gas composition in Figures 4 to 6.
Oxygen enriched air gasification reduced nitrogen dillution and enhanced combustible gas Low ER produced more concentration of combustible gas in the gas production.
LHV increased because steam enhanced the reforming reactions, watergas, and water-gas shift reaction, and then decreased if Within the range considered in this study, the highest LHV from cob gasification was 8.
08 MJ/m3 at 50% OC.
ER of 0.
15 and SB of 0.
23 and the highest LHV from the stover gasification was 8.
17 MJ/m3 at 50% OC.
ER of 15 and SB of 0.
It should be noted that the LHV calculated in this work considered only H2.
CO, and CH4.
Other hydrocarbon gases, such as C2 and C3, were not measured and considered.
The actual LHV of the gas may be slightly higher than the reported here.
Biomass pretreatment by torrefaction may improve gas quality to higher LHV.
Although the high LHV was obtained in oxygen enriched air gasification with low ER, the volume of the produced gas was low.
The gasification efficiency should be further considered.
Fig.
5 Effect of operating conditons on CO production in % v/v .
hown as Y-axi.
from gasification of corn cob .
and stover .
SB = 4 .
ER = 0.
25, and .
OC = 30% A IJRED Ae ISSN: 2252-4940.
All rights reserved Citation: Sittisun.
Tippayawong.
, and Shimpalee.
Gasification of pelletized corn residues with oxygen enriched air and steam.
Int.
Journal of Renewable Energy Development, 8.
, 215-224, doi.
org/10.
14710/ijred.
P a g e | 222 5 Effect of operating conditions on gasification efficiency Gasification efficiency is important in considering optimum condition when utilizing this gas for energy.
It is defined as the ratio between the energy content of the gas product and the energy content of the biomass input.
Increasing OC in enriched air was not found to be significant to the gasification efficiency.
Although the higher OC led to higher LHV, the gas production was This observation was similar to Zheng et al.
( 2.
who reported bio- oil gasification using air, enriched air and oxygen as gasifying agents.
Nam et al.
( 2.
used daily manure as feedstock in a fluidized bed gasifier and reported insignificance of oxygen concentration on gasification efficiency.
Breaking down and partially oxidation of the biomass, tar and other intermediate products led to higher gas yield and an increase in gasification efficiency when ER was However, using excessive air resulted in higher .
degree of oxidation of the combustible product gases (H2.
CO, and CH.
, hence, the efficiency was degraded.
SB seemed to be the most significant factor affecting the gasification efficiency, as it was increased with increasing SB.
Similar agreement was reported by Wang et al.
( 2.
and Kumar et al.
( 2.
, in which it was expected that the excess steam would decrease gasification temperature.
Appropriate amount of steam would increase the efficiency.
Within the range considered, the highest gasification efficiencies were 39.
4% for cob at the condition of ER = 0.
27 and SB = 0.
57, and 42.
82% for stover at ER = 0.
21 and SB = 0.
Although the use of higher oxygen concentration in enriched air gasification did not significantly affect gasification efficiency, lower nitrogen dilution led to higher burning temperature which was useful for the high temperature heating systems (Sittisun and Tippayawong, 2019.
Punnarapong et al.
, 2.
Fig.
6 Effect of operating conditons on CH4 production in % v/v .
hown as Y-axi.
from gasification of corn cob .
and stover .
SB = 0.
ER = 0.
25, and .
OC = 30% A IJRED Ae ISSN: 2252-4940.
All rights reserved Int.
Journal of Renewable Energy Development 8 .
2019: 215-224 P a g e | 223 Conclusion increased gas yields, but decreased combustible gas components and LHV of the producer gas.
Applying steam was observed to favor mainly H2 production, whereas CO and CH4 production was LHV and gasification efficiency was found to initially increased, and then decreased at higher amount of steam.
The highest LHV from cob gasification was 8.
MJ/m3 at 50% OC.
ER of 0.
15 and SB of 0.
23, while the highest LHV from stover gasification was 8.
17 MJ/m3 at 50% OC.
ER of 0.
15 and SB of 0.
The highest gasification efficiency was 39.
44% at ER of 0.
27 and SB of 58 for cob gasification, and 42.
82% at ER of 0.
21 and SB 8 for stover gasification.
Gasification of corn cob and stover using oxygen-enriched air and steam mixtures as gasifying medium has been Effects of oxygen enrichment from 21 to 50%, equivalence ratio between 0.
15 and 0.
35, and steam to biomass ratio from 0 to 0.
8 were investigated.
Both types of feedstock materials behaved in similar ways.
The use of oxygen enriched air reduced the nitrogen dilution effect.
Increasing oxygen was observed to increase combustible gas (H2.
CO, and CH.
proportion and LHV.
Changing air gasification to 50% OC gasification.
LHV was improved 04 to 6.
77 MJ/m3 for cob, and 4.
21 to 6.
94 MJ/m3 for stover, respectively.
An increase in equivalence ratio .
LHV .
LHV .
LHV .
Fig.
7 Effect of operating conditons on LHV in MJ/m3 .
hown as Y-axi.
from gasification of corn cob .
and stover .
SB = 0.
ER = 0.
25, and .
OC = 30% A IJRED Ae ISSN: 2252-4940.
All rights reserved Citation: Sittisun.
Tippayawong.
, and Shimpalee.
Gasification of pelletized corn residues with oxygen enriched air and steam.
Int.
Journal of Renewable Energy Development, 8.
, 215-224, doi.
org/10.
14710/ijred.
P a g e | 224 Gasification eff.
(%)
Fig.
8 Effect of operating conditons on efficiency in % .
hown as Y-axi.
from gasification of corn cob .
and stover .
Acknowledgments The authors wish to acknowledge the supports from Thailand Research Fund (RSA5680.
, and Chiang Mai University.
References